 |
 |
 |
|
XTV3G22E-F8 pump from Annovi Reverberi. The XTV3G22E-F8 is rated with a flow rate of 3 Gallons Per Minute at a maximum PSI of 2200. The pump spins at 3400 RPM and is built to last you a lifetime. With a forged brass head, die cast body, solid ceramic plungers, bronze connection rods and the best stainless steel and rubber and plastic internal elements that AR Pumps could get for the construction of this unit. If you need parts for this XTV3G22E-F8 pump please find them on the parts breakdown by clicking here. After finding the parts or kits you need just enter any part number from the breakdown in our search box for pricing and availability. Please be aware this pump will also replace Hypro Model #: 2269B-A, and can be written as XTV3G22E, XTV3G22, XTV3G, XTV3, or even simply an XTV pump.
Notes on oil capacity for different PSI running of this pump are below.
PSI < 1740 = Oil Capacity = 8 oz, Maximum Fluid Temperature = 140° F,
Inlet Thread = 1/2”F, Discharge Thread = 3/8”F
PSI > 1740 = Oil Capacity = 10 oz, Maximum Fluid Temperature = 140°,
F Inlet Thread = 1/2”F, Discharge Thread = 3/8”F
It is recommended that you use AR64516
Oil (click link to view/purchase oil). It is also suggested that you first change oil after 50 hours of use. Then you need to only change it once every 500 hours or so.
- Manifold:Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety, performance.
- Inlet and Discharge Ports: Heavy bosses for added strength.
- Offset Discharge Ports: High efficiency, smooth flow.
- Bolts: Six Bolts, 6mm, grade 12.9.
- Valves:Ultra Form Cages: Durability, strength and long life.
- Poppets, Seat and Spring: 303 and 400 series stainless steel.
- Valve Caps: Machined brass – greater strength.
- Packing and Plungers:
- High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
- Low Pressure Seals: “U” cup double lip Buna-N. Good positive seal.
- Support Guides: Machined brass one-piece construction to assure proper plunger alignment and to maximize packing and seal life.
- Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
- Bearings: Over sized for maximum life and load disbursement, two ball bearings on the solid shaft series and a needle bearing on the drive side and ball on the non-drive side for the hollow shaft series. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
- Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
- Rear Cover: Precision die-cast, precision punched gasket sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
- Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
- Rod Pins: Precision ground and hardened steel, over sized for load disbursement.
- Connection Rods: One piece special alloy aluminum based and bronze, over sized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
- Crankshaft: Forged one-piece, precision ground and hardened for extremely long life and durability.
- Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
- Oil Capacity: Flat cover 8 oz. and extended cover 10 oz.
- Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
- Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
- Hot Water: High temperature kits are available to 180º F. Refer to breakdown.
- Wet End Repair: Very simple no special tools are required.
- Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
- Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
Items NOT INCLUDED with your pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
The PUMP GUARD will 'dump' any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)
PRESSURE REGULATOR / UNLOADER - if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
The INLET WATER FILTER will catch most small debris before it enters your pump
The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Triplex Plunger Pump
- Direct Drive with Electric Flange NEMA 56C
- Max. Volume: 3.0 GPM
- Max. Discharge Pressure: 2,200 PSI
- Max. Pump Speed: 3400 RPM
- Shaft Diameter: 5/8” Hollow
- Minimum Horsepower Requirements: 4.5 BHP
- Max. Fluid Temp.: 160 degrees F.
- Inlet Ports (2): 1/2" BSP
- Discharge Ports (2): 3/8" BSP
- Drive Side: Standard right
- Forged brass head & valve covers
- Solid ceramic plungers
- Weight: 9.0-11.0 lb
- Replaces the following:
- Hypro Model #: 2269B-A
- Max Flow (in GPM): 3.0
- Max Pressure (in PSI): 2200
- Pump Speed (in RPM): 3400
- Shaft Diameter: 5/8", Hollow
- Cat Model #: 2SFX30GES
- Max Flow (in GPM): 3.0
- Max Pressure (in PSI): 2000
- Pump Speed (in RPM): 3400
- Shaft Diameter: 5/8", Hollow
- Cat Model #: 2DX27ES.MIST
- Max Flow (in GPM): 2.7
- Max Pressure (in PSI): 2000
- Pump Speed (in RPM): 3450
- Shaft Diameter: 5/8", Hollow
|
|
|
|
|
|
|
|
| Accessories for this product... |
|
|
|
|